Create Center Points from Curvesv3.0.2
Creates a point at the center of every selected arc or circle curve and puts the new points in a group.
Free List price $19
All 261 tools in the library, 81 of them free. Search and filter; the address of a filtered view can be shared. How pricing works
Creates a point at the center of every selected arc or circle curve and puts the new points in a group.
Free List price $19
Groups every solid in the model whose volume is greater than 0 and less than a maximum you enter, on the assumption that these small solids are fasteners.
Places points along each selected curve: a number of equally spaced points, a fastener-style row at a minimum pitch and edge distance, or one point at a given distance.
Free List price $79
Creates lines of a given length along the axes of selected cylindrical surfaces, or of the first cylinder on each selected solid, for example fastener axis lines.
Creates lines of a given length from selected points or nodes, along a surface normal, the average normal of plate elements, a picked vector or a curve tangent.
Creates a geometry line along each selected CBUSH, from its first node to its second, or a line of a fixed length centered on the CBUSH and along its direction.
Creates a chain of lines, or one spline, through a set of points or nodes.
Free List price $79
Creates a node at every selected point, or a point at every selected node.
Free List price $39
Makes one surface from the elements of each selected group, keeping the mesh associated to it, so many parts are surfaced in one run.
Creates a point at the virtual sharp of a fillet curve or of two curves, where the tangent lines at their ends meet when extended.
Creates offset curves of every edge of a selected surface at a given distance, in the surface, like Geometry > Curve - From Surface > Offset Curve/Washer.
Free List price $19
Creates points from X, Y, Z coordinates on the clipboard, for example three columns copied from Excel (one point per row, tab-separated).
Creates a point where each selected curve intersects a selected surface.
Changes every selected curve that is geometrically straight (a straight spline, for example) into a Femap line curve.
Free List price $19
Extends selected straight curves by a length, at their end, their start or both ends.
Free List price $39
Deletes every curve in the active model in one step, without asking.
Free List price $19
Deletes every point in the active model in one step, without asking.
Free List price $19
Deletes the selected solids whose title contains a keyword (case-sensitive).
Writes the selected points to a STEP file on the desktop, in millimeters or inches, that CAD imports as a part, for sending hard points to CAD.
Create Femap points or nodes from a table of coordinates (or GRID cards for HyperMesh, ANSA or a deck), and find the nearest node to any location.
Free List price $595
Creates a rectangular coordinate system from a picked line element, with its origin at the first node, X toward the second node and XY plane along the element orientation.
Deletes coordinate systems that other entities still reference, after moving those references to the global system or another CSys, or groups each CSys with what uses it.
Groups, for each coordinate system, the nodes that use it as output or definition CSys and optionally the properties that reference it, or lists the counts per CSys.
Finds the centroid (average location) of selected nodes or points, then creates a node there, creates a point there, or moves selected nodes there.
Creates a point or a node at the volume centroid (CG) of each selected solid, using the solid ID as the new ID when it is free.
Creates copies of selected nodes or points projected onto selected curves or surfaces, at the closest point or along a picked vector; the originals do not move.
Moves selected nodes to equally spaced locations, keeping their order, along a curve or on the straight line between two end nodes.
Moves a node to the mirror image of another node across a symmetry plane, to make a mesh match on both sides of a symmetric model.
Moves nodes onto other nodes and merges them in one go, like Modify > Move By > Node followed by Tools > Check > Coincident Nodes.
Moves one node to the intersection of two vectors.
Tapers a mesh: moves selected nodes along one direction of a coordinate system by an amount that varies linearly along another direction, set by a start node and an end node.
Deletes every node in the active model in one step, without asking, and reports how many were deleted.
Free List price $19
Deletes the selected nodes that the model does not use, together with any loads and constraints on them, for example the orphan nodes left after re-meshing.
Exports the selected nodes to a new Excel workbook, one row per node.
Free List price $19
Models a flange (or doubler) laid up on top of existing laminate shells as a second, coincident layer of shells.
Joins pairs of (nearly) coincident nodes with plot-only line elements, so nodes that are meant to stay separate (CBUSH or joint modeling) are not merged by a later coincident-node check.
Adds the mass of modeled elements to a mass element (CONM2), or subtracts it, for example when part of a lumped mass is now modeled with elements.
Carries the material direction of picked source elements across the folds of a formed laminate part (bucket rib, channel) onto the neighboring flange elements.
Replaces one node with another in the connectivity of the selected elements.
Copies the property ID and/or the plate offset of a picked "source" element onto the selected elements of the same element type.
Fixes inverted (negative volume) linear wedge and pyramid elements, such as those made by Laminate to 3D Core.
Moves the nodes of the selected plate or laminate plate elements along the element normal, by half the thickness, the whole thickness or a fixed distance, to the + or - side.
Sets the orientation vector of selected line elements (beams, bars, CBUSHes) from a curve tangent, the normals of adjacent plates, or square to the element axis.
Puts a point mass element (Nastran CONM2) on every selected node in one go.
Free List price $39
Swaps node 1 and node 2 of the selected 2-node line elements (CBUSHes or any other line element), reversing their direction.
Groups the selected plate and line elements that have element offsets, and the beam properties of the line elements that have offsets, in up to three groups.
Free List price $79
Lists the elements that reference both of two selected nodes, a quick check of what (if anything) connects them.
Free List price $19
Measures the combined mesh mass properties of any selected elements (shells, solids, beams, mass elements, ...) and copies them to the clipboard as a tab-separated header row and value row, ready to paste into a spreadsheet.
Free List price $19
Groups the free-ended nodes of the selected line elements (nodes on no other element) with their elements, and puts grounded springs in a separate group.
Exports one row per selected element (centroid, type, property, material, length, area, volume, optional face normal and material direction) to Excel, the Data Table or the message window.
Groups the selected elements that use an orthotropic or anisotropic material but have no material orientation, and the plates whose material direction strays from the rest.
Lists, sets and/or rounds the element offset (ZOFFS) of the selected plate and laminate elements (linear and parabolic).
Free List price $39
Runs Femap's element quality checks (aspect ratio, taper, warping, Jacobian, skew, tet collapse) on selected elements, groups the failures and can build a PowerPoint of them.
Free List price $79
Weigh the model, reconcile it with the weight statement, add corrective masses, and balance loads.
$1,995
Tell me when it is readyTurns beam elements into solid elements with the shape of the beam section.
Converts the selected laminate plate elements into laminate solid elements by extruding them along their normal by the laminate thickness.
Turns cored laminate plate elements into two facesheet laminates with a 3D solid core between them.
Mirrors the selected elements across a plane you pick into new nodes and elements, with mirrored copies of their properties, layups and coordinate systems.
Builds an equivalent beam (stick) model from a shell mesh.
Fills a region bounded by a closed loop of element edges with a transition mesh.
Combines pairs of TRIA3 elements into QUAD4 elements, one pair at a time.
Remeshes a contiguous patch of linear shell elements that share one property.
Smooths peaks (spikes) in a shell mesh at the nodes you select, bringing each one back in line with the mesh around it.
Finds fastener stacks among selected points or nodes (points within a grip length of each other) and connects each stack with a line, CBUSHes of the stiffness you enter, or both.
Connects source nodes (for example the nodes of an L-clip or similar bracket) to target shell elements with RBE3 + CBUSH pairs.
Removes duplicate entries from connection regions.
Creates CBUSH fasteners with their stiffness, one per selected fastener line, through the plates the line goes through.
Ties the selected nodes to a center node as a rigid body with MPCs instead of a rigid element.
Groups the selected CBUSHes by length (zero length within a tolerance, or longer) and groups stacked CBUSHes, those that share a node with another CBUSH.
Free List price $79
Creates a fastener through a stack of 2 or more plates from Femap picks (for many fasteners, use the Fastener Manager workbook).
Connects hole pairs in two parts with a CBUSH between RBE2 spiders built on the hole-edge curves, or links existing top and bottom spiders with CBUSHes.
Creates RBE2 or RBE3 spiders on selected nodes, curves, surfaces or the holes of solids, with a new center node, or from existing center nodes to the nodes within a distance.
Checks, and optionally straightens, the co-linearity of the selected CBUSH and/or GAP fasteners.
Batch-edits the selected RBE2 and RBE3 elements, setting their DOFs and RBE3 leg weights, or removing chosen nodes or midside nodes from their legs.
Groups the center node (node 0) of the selected rigid elements, either in separate "RBE2 Center Nodes" and "RBE3 Center Nodes" groups or in one "Rigid Center Nodes" group.
Shortens CBUSHes to a small length by moving their end nodes along the CBUSH axis, so the CBUSH direction does not change.
Points the selected connectors (contact / glued connections) at a different connection property.
Exports the selected CBUSHes (or all) to a new Excel workbook with their nodes, properties, stiffnesses and orientation, and their forces per output set with the maximum tension and shear.
Shows the orientation of the CBUSHes visible in the active view as arrow triads (user graphics) at each CBUSH's spring location, or clears them.
Checks the selected RBE2s and RBE3s for free leg nodes, center nodes repeated as legs, DOFs dependent in two rigid elements and RBE3 rotations or weights, and groups what it finds.
Lists the elements in both regions of each selected connector in a new Excel workbook.
Free List price $39
Create, list and update CBUSH fasteners and their stiffness (between plates, through solid stacks or through plate stacks, found from the holes in the mesh), edit their properties, nodes and orientation, and read their forces, in Femap, HyperMesh, ANSA or a Nastran deck, without leaving Excel.
$4,995
Tell me when it is readyEdit every RBE2/RBE3 in Femap, HyperMesh, ANSA or a Nastran deck - and create new ones at fuselage stations - without leaving Excel.
$1,995
Tell me when it is readyRuns, in ANSA, the task a Fastener Manager, RBE Manager or Card Editor workbook writes (list, edit or create RBEs, CBUSHes, PBUSHes, materials and properties) and returns the result to Excel.
Runs, in HyperMesh, the task a Fastener Manager, RBE Manager or Card Editor workbook writes (list, edit or create RBEs, CBUSHes, PBUSHes, materials, properties and masses) and returns the result to Excel.
Finds the faces where the parts you give it touch and sets up a tie contact for each pair as main and secondary sets, which can be seen, changed or dropped.
Copies the properties of selected elements (with their layups) to new IDs and assigns the copies to those elements only, or copies one picked property to a typed ID.
Free List price $79
Creates beam and bar properties with a cross section scaled by a factor from one property, or tapered along the elements between a start and an end element.
Replaces every zero stiffness term (K1 to K6) of the selected spring/CBUSH properties with a user value, so no CBUSH DOF is left without stiffness.
Finds duplicates among the selected properties of one type and moves the elements of each duplicate onto the first property it matches.
Renames the selected rod, bar, shear panel and plate properties from their type, material title and size.
Batch-edits the selected plate and laminate properties, rounding thicknesses, setting non-structural mass from the structural mass or a scale, and clearing bending and shear materials.
Copies a short description of one property to the clipboard, ready to paste into a report or a note.
Free List price $39
List, edit and write Nastran cards for materials, properties, layups and loads.
Cut plates and beams with a plane and get the section's axial and bending stiffness.
Creates a new layup from the cells selected in a running Excel.
Creates sandwich laminate variants with the core ply of one property scaled by a factor, or ramps the core thickness across selected elements between a start and an end node.
Adds plies to or removes plies from the selected layups.
Finds plies in the selected layups and changes their angle, thickness and/or material.
Renames the selected layups from their plies, in the form <plies>P_<thickness><unit>_<Cored or NC>_<a>% / <b>% / <c>% for example 12P_0.0936in_NC_33% / 50% / 17%.
Free List price $39
Audits or sets one option of laminate plate properties (linear and parabolic), for selected properties or every laminate property in the model.
Overwrites the ply stack (materials, thicknesses, angles and global plies) of one or more selected layups with the plies of an existing layup.
Lists, for each selected layup, the plies under and over the core, the core thickness and the core material in the Data Table, and copies the table to the clipboard.
Free List price $39
Exports the laminate properties of selected layups (engineering constants, thickness, and A, B and D matrices) to the Data Table or a new Excel workbook.
Free List price $79
Exports the layups of the selected laminate properties to a new Excel workbook as ply tables with their ply mix, a mass per area summary and a colored layup plot.
Free List price $149
Constrains RX, RY and RZ on every node, corner and midside, that is used only by solid elements (tetra, wedge, pyramid and brick), since solids have no rotational stiffness.
Builds the boundary loads of a breakout (sub-model) region from the results of the global model.
Maps element pressures from another open model, or a Nastran file, onto a group of the active model with a different mesh, or turns pressures into data surfaces and back.
Replaces the nodal loads on a set of nodes by one statically equivalent force and moment on a new node at their centroid.
Adds one load set, with scale factor 1.0, to each selected load combination set.
Compares the applied loads of a source region, which may be in another open model, with those of a target region, and balances the target to match.
Moves the element pressures of the selected load sets to another element face (face 1 by default).
Removes repeated references from combination load sets and combination constraint sets.
Renames the selected load sets from the output set they were made from (its subtitle, title or case title), or adds a prefix to their current titles.
In each selected load set, moves the loads on the entities of a chosen group out of their load definitions into a new load definition named after the group (one per load type in each load set).
Finds and deletes true duplicate loads in the selected load sets.
Lists, in the message window, which of the selected load sets load the picked elements or nodes, or which of the selected groups hold them.
Free List price $39
Creates a group of the elements and nodes that carry loads in the selected load sets, or of those that carry none, taken from the whole model or from the active group.
Groups every node of the model that is constrained on any degree of freedom, in a new group.
Writes the nodal forces and moments of the selected load sets to a new Excel workbook, one row per load.
Sums the applied loads of each selected load set about a picked location, in a chosen coordinate system, and writes one row per load set to a new Excel workbook.
Writes a Nastran bulk data file (.dat) holding only the load cards of each selected load set, to a chosen folder (the model folder by default), named <load set ID>_<date-time>.dat.
Builds the shear, moment and torque (VMT) distributions along a load reference axis for several load sets.
Creates load sets, nodal forces and moments, accelerations, pressures and enforced displacements from an Excel table, in Femap or as a Nastran include for HyperMesh, ANSA or a deck.
Bring loads back into a remeshed model, or onto a breakout model, from the open model that has them.
Creates one analysis set per pair of selected constraint and load sets from a template, or combines the cases of selected analysis sets into one set with a subcase each.
Batch-edits the selected analysis sets in one dialog, setting the solver, write group, file names, case titles and IDs, bulk data text and other options.
Writes the selected analysis sets as Nastran decks, with an optional batch file that runs them, or runs them in Femap now or at a set time.
Writes one Nastran deck of an analysis set for each value in a sweep from a start to an end value, to the model folder.
Audits every analysis set in the model for settings that make the model hard to share or that hide modeling errors, lists each problem in the message window and optionally fixes it.
Free List price $79
Creates one NX Nastran modal analysis set, with no constraints, that runs the Nastran weight check, the grounding check, or both, and optionally runs it.
List, edit and create Femap analysis sets, cases, boundary conditions, output requests and Nastran options without leaving Excel, or read and write them as an OptiStruct or Nastran run deck that includes a model from ANSA or HyperMesh.
$1,995
Tell me when it is readyRemoves the midside nodes of the parabolic elements attached to the selected nodes from the current node selection, leaving the corner nodes.
Free List price $19
Reduces the current element selection to line elements.
Free List price $19
Reduces the current element selection to laminate plate elements (linear and parabolic).
Free List price $19
Reduces the current selection to the entities that are also in a second set you pick.
Free List price $19
Reduces the current element selection to the elements that use properties you pick.
Free List price $19
Reduces the current node selection to the midside nodes of the parabolic elements attached to the selected nodes.
Free List price $19
Removes the nodes attached to elements you pick from the current node selection.
Free List price $19
Reduces the current node selection to the nodes attached to elements you pick.
Free List price $19
Reduces the current element selection to plot-only elements (plot lines and plot plates).
Free List price $19
Reduces the current element selection to the interpolation rigid elements (RBE3s).
Free List price $19
Reduces the current solid selection to sheet solids.
Free List price $19
Selects, in the selector, the layups used by the selected properties.
Free List price $19
For each picked element, adds the node at a given position in the element's node list (for example node 1, the first node of every element) to the node selection.
Free List price $19
Adds to the property selection the properties, among those you pick, whose title contains a search text, with or without matching case.
Free List price $19
Copies the IDs of the entities in the selector (nodes, elements, properties, geometry and more) to the clipboard, one per line or comma-separated.
Free List price $39
Adds an "element by property" rule to each selected group for every property used by the elements already in it, so elements created later with those properties (for example elements reflected to the other side of the model) join the group when it is next evaluated.
One-click shortcut: adds the nodes of the active group's elements to the active group (like Group > Operations > Add Related for nodes only).
Free List price $19
Adds entities to, or removes them from, many groups at once without creating new groups.
Cleans the selected groups by entity type, keeping only the types you check or removing what brings those types in, and can add the related entities back.
Creates a layer for each selected group, with the group's title, its ID and a random color, and moves the group's elements and nodes onto it.
Free List price $19
Grows the active group (or several groups in turn) by element connectivity, one layer of connected elements at a time, for the number of layers you type or until nothing more is added.
Grows a set you pick in ANSA by connected elements, one layer at a time, never across CBUSHes, rigids, springs, beams or masses.
Rebuilds each selected group from its solids or from its surfaces.
Removes the CBUSHes and/or rigid elements of the model from the selected groups, together with every element connected to them and all the nodes of those elements.
Removes file paths from group titles.
Free List price $19
Finds the nodes at selected points and adds them to the active group or to a new "Nodes at Points" group.
Groups the selected curves that lie on any of the selected surfaces, in a "Curves On Surfaces" group.
Free List price $19
Groups the selected elements whose centroid lies within the threshold distance of any of the selected curves, in an "Elements On Curve" group.
Free List price $19
Finds the materials and rigid elements that may be missing thermal expansion data and puts them in groups to examine.
Groups the interface nodes of the selected groups (nodes shared with elements outside them), per group, for the groups combined, or split into internal and external.
Checks the selected nodes against the selected straight lines (for example fastener lines) and groups the nodes that lie on a line.
Groups the selected planar elements (shear panel, membrane, plate, laminate and plot-only plate) by face area.
Finds the red (color 4) points and nodes in the model and creates up to three groups.
Free List price $19
Makes a group of the whole model ("Whole Model") or of all its geometry.
Free List price $39
Writes a summary of each selected group to a new Excel workbook, one row per group.
Writes the groups, layers, entity colors and freebodies of a model to a text file and reads that file back onto another model, for example one rebuilt from a bulk deck.
Replaces the mesh of a region of the active (target) model with the updated mesh of the same region from another open (source) model, for example a part remeshed in its own model.
Writes the Nastran bulk data of the selected groups to .bdf files and removes the executive and case control decks (header) and the ENDDATA line, so the files can be included in another deck.
Writes the ANSA sets you pick, with their nodes, properties and materials, to one Nastran bulk data file ready to include in another deck.
Colors the elements of each selected group, either with a random color for each group or with one specified Femap color for all of them.
Free List price $19
Gives each group its own node and element ID range, for models numbered by component.
Renumbers groups, properties, layups, materials or load sets so that their IDs follow the alphabetical order of their titles (not case sensitive), starting at the ID you type.
Gives the layup of each laminate property (plate or solid) the same ID as the property.
Renumber and retitle Femap entities from Excel, give each group its own ID range, and keep one ID plan for decks moved between ANSA, HyperMesh and Femap.
Estimates the interlaminar shear stress that a chain of beams (for example a stiffener cap modeled with beams on a skin) puts into the structure at each node.
Copies the selected output vectors to new vector IDs in each selected output set.
Writes one numeric column of the Data Table to a new output set ("Output from Data Table") as a nodal or elemental scalar vector (ID 400000, titled like the column), so any Data Table calculation can be contoured.
Envelopes the solid element stresses of the whole model over picked output sets into new output sets of max principal, min principal and von Mises stress.
Builds an XY function from two output vectors of one output set.
Writes each selected element's distance along a chain of curves as an output vector, to contour or plot results along a path.
Creates a new output set holding the difference of the plate membrane forces (Nx, Ny, Nxy) of two output sets, A minus B, element-oriented or in the material direction.
Adds the principal membrane forces of the selected plate elements (max, min, max shear and angle from the material axis) to each selected output set.
Turns the elemental plate top-surface total strains of the selected elements into nodal values, averaged at each node, in microstrain, and writes seven new nodal vectors into each selected output set.
Converts the element pressures of the selected load sets into output vectors, one per load set, titled with the load set title, so they can be contoured.
Creates a new output set holding the ply count, core thickness or property thickness of each selected element, as an elemental vector to contour.
Creates output vectors at selected nodes of their displacement relative to the nearest reference node, or their deflection normal to the attached shells, in each selected output set.
Rotates plate forces, stresses or strains into a frame along the nearest selected curve, and writes them as new output vectors.
Retitles the selected output sets by cutting the label after the first comma, adding each set's eigenvalue, frequency or time to its title, or both.
Keeps interface freebody summation points attached to nodes, so they follow the mesh after re-meshing or moving nodes.
For each selected output set of a normal modes analysis, sorts the selected elements by strain energy and splits them into two groups.
Finds the node and DOF where each selected buckling mode peaks among the selected nodes, and lists them with the element strain energy there in the Data Table.
Sends the selected element output vectors, for the elements of the selected groups, to the Data Table, and adds a "Group" column with the title of the first selected group that contains each element.
Lists the ID and title of the selected output sets, and optionally their notes, either in the message window or in the Data Table.
Free List price $39
For each selected output vector, envelopes the selected elements over the selected output sets and lists in the message window the minimum, maximum and maximum absolute value, each with the element ID and the output set where it occurs.
Free List price $19
Exports freebody summations to a new Excel workbook or a CSV file.
Exports plate results transformed to the material direction to a new Excel workbook.
Writes a per-ply stress report for the selected laminate elements in the active output set to a new Excel workbook.
Sets a section cut plane in the active view and switches the view to a section cut contour.
Writes, at each selected node, the lowest buckling eigenvalue among the modes that move it and that mode's output set, into a new output set to contour.
Finds the line of action of the resultant force of selected elements on selected nodes in the active output set, draws it as a line and reports its point and force.
Keeps joints (lists of plate element edges) in the model and writes their running loads for selected output sets as output vectors, to a new Excel workbook, or both.
Computes joint (bondline or interface) stresses and running loads at the nodes of selected element faces or edges, from freebody nodal sums.
Checks sandwich panels per element and output set for core shear, facesheet wrinkling, core crimping and intracell dimpling, and writes the strength ratios as output vectors.
Reads a Nastran .f06 file into a new Excel workbook as a table of eigenvalues per subcase, or of the load and SPC force resultants of each static subcase.
Exports the loads carried by the selected rigid elements (RBE2 / RBE3) for the selected output sets to a new Excel workbook.
Writes, for each selected mode, the share of strain and kinetic energy in each selected group to a new Excel workbook, to tell which part each mode moves.
Groups the elements (elemental output) or nodes (nodal output) that pass the criteria limits of the active view.
Reads a Nastran output file (.f06 or .out) and groups every node listed in the grid point singularity table or in the pivot ratio (matrix/factor diagonal ratio) table, in a "Singularities and Pivot Ratios <file name>" group, so the poorly constrained nodes can be displayed on the model.
Toggles the preference that sets the titles of output sets read from Nastran OP2 files between Default and SUBTITLE (the subcase subtitle).
Free List price $19
Computes the preload range, bolt and joint stiffness and every margin of preloaded bolted joints to NASA-STD-5020B, for many bolts and load cases typed or pasted from your model.
Envelope joint and fastener loads from Femap output or from Nastran / OptiStruct results files.
Turn a table of node or element values into Femap output vectors, and read a vector back.
Rebuilds the model, then saves it.
Free List price $19
Updates existing coordinate systems and CONM2 masses to a configuration stored in a small-field (8-character) Nastran file of CORD2R and CONM2 cards, for example to switch a model between mass or geometry configurations.
Reads every file in a folder (and optionally its subfolders) that matches an extension into the active model, one after the other, as Nastran decks or Parasolid files.
Opens a new model, reads an NX Nastran input file into it and attaches the results file (.op2) with the same name from the same folder, in one step.
Free List price $19
Writes a copy of a bulk deck with each Femap property comment changed to a Patran region comment, so the property names come through in Patran.
Comment cards out of a Nastran deck, and read, edit and write TEMP cards.
Write Nastran decks in NX or MSC dialect through Femap; without it, turn a deck into OptiStruct form or back, rewrite its field format, and carry property and material names between Femap, HyperMesh and ANSA.
Trace a Nastran deck's include tree, flatten it into one file, inventory its cards and broken references, and compare two decks.
Reads an NX Nastran, MSC Nastran or OptiStruct deck (it tells which, and reports it), and its f06 when there is one, and writes one HTML report next to it that breaks the model down for its author and for someone who has never seen it.
$3,495
Tell me when it is readySaves the active view (orientation and every display setting) as a new view with a title and ID you choose, or over an existing view, which keeps its title.
Copies a view orientation from a picked view to the active view, from the active view to every other view, or to the active view of every other open model.
Sets the color of one property to the color of another picked property, without typing a color number.
Free List price $19
Moves the clipping plane of the active view one step along its normal, a one-click nudge for a hotkey.
Free List price $19
Moves the clipping plane of the active view one step against its normal, a one-click nudge for a hotkey.
Free List price $19
Turns on the clipping plane of the active view through a node or point, cutting away what is in front of it when looking in the chosen view direction.
Builds a color key (legend) in a new Excel workbook for the properties used by the elements visible in the active view.
Free List price $19
Toggles the 3D solid bodies (not the sheet solids) in and out of the display with the Draw/Erase toolbar, so sheet or midsurface geometry can be worked on without the solids in the way.
Free List price $19
Turns the active view to look straight at a picked shell element, centered on its first node, with screen-right along the element's material direction.
Toggles the element ID labels of the active view on and off.
Free List price $19
Toggles the display of freebodies in the active view.
Free List price $19
Shows the line elements and hides the plates and laminates, or the reverse, or shows both, in one choice.
Toggles the display of element material directions, together with element offsets, in the active view.
Free List price $19
Toggles the node ID labels of the active view on and off.
Free List price $19
Makes every property visible again, so all elements hidden by property visibility are shown.
Sets up the active view for checking properties by color, giving every property a random light color on a dark background with other entities hidden.
Free List price $39
Flips the clipping plane normal of the active view, so the other side of the plane is shown.
Free List price $19
Rotates the active view 90 degrees about the viewing direction (the line of sight stays the same, screen-up turns 90 degrees).
Free List price $19
Snaps the active view to the back preset, one of six one-click view presets (Front, Back, Left, Right, Top, Bottom) meant for hotkeys or a toolbar.
Free List price $19
Snaps the active view to the bottom preset, one of six one-click view presets (Front, Back, Left, Right, Top, Bottom) meant for hotkeys or a toolbar.
Free List price $19
Snaps the active view to the front preset, one of six one-click view presets (Front, Back, Left, Right, Top, Bottom) meant for hotkeys or a toolbar.
Free List price $19
Snaps the active view to the left preset, one of six one-click view presets (Front, Back, Left, Right, Top, Bottom) meant for hotkeys or a toolbar.
Free List price $19
Snaps the active view to the right preset, one of six one-click view presets (Front, Back, Left, Right, Top, Bottom) meant for hotkeys or a toolbar.
Free List price $19
Snaps the active view to the top preset, one of six one-click view presets (Front, Back, Left, Right, Top, Bottom) meant for hotkeys or a toolbar.
Free List price $19
Mirrors the active view about the model's symmetry plane, to look at the same spot on the opposite side of a symmetric model.
Toggles the display of element thicknesses and offsets in the active view.
Free List price $19
Turns on the workplane at the global origin in the XZ plane, with its grid and rulers, so station numbers (X) can be read off the model.
Builds a PowerPoint presentation of coordinate systems, for example the locations and orientations of accelerometers.
Saves the colors of the selected elements to a text file (one "element ID, color" line per element), or loads such a file and gives every element of the open model that has a listed ID its saved color.
Sets Femap's current directory (and the macro current directory) to the folder of the current model file, so file dialogs and macros that use relative paths start there.
Free List price $19
Creates or updates a model ID text box on screen with the model file name, a date and time stamp and the Windows user name.
Reports the first unused ID at or after a start ID for an entity type (element, node, property, layup, solid, surface, curve or point), and the next ID after the highest one in use.
Free List price $39
Lists the UserData objects stored in the model (data that macros keep with the model, such as joint definitions, freebody associations or settings) with their sizes and the total memory used, then optionally deletes the selected objects or all of them, after a confirmation.
Free List price $39
Measures the straight-line distance between two nodes, copies it to the clipboard (full precision) and prints it in the message window (3 decimals).
Free List price $19
Turns the display of user graphics (the arrows, lines and labels that macros draw with Femap's GFX objects) back on in all views.
Free List price $19
Compares the elements of two models and creates a group in each model of the elements that were not found, or did not match, in the other.
Measures the angle between two elements (line element axes or plate normals, and the orientation vectors of two line elements) or between two picked planes, in degrees.
Free List price $39
Labels elements in the graphics window with their property info, to document ply and thickness regions.
No tools match your search or filters.